Each person will have their own unique theory on the subject of How to Install a Bathtub Yourself.
Setting up a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably hard task. If the old tub is conveniently easily accessible, the job can relocate rapidly; if you need to open a wall to get rid of the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old tub as well as set in the new one. See to it you have actually qualified on your own for the work and are comfortable trying it. As opposed to hiring a professional to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This write-up will assist you mount a brand-new bathtub in your washroom if you have actually already gotten a new bathtub as well as do not require to transform the setup of your previous supply of water pipelines.
Your devices as well as product list ought to comprise the following:
Planning for the Setup
To start with, the supporting framework provided with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to ensure that if the tap features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its final position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome as a result of the limited access that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the remaining water that will come from the pipes. When the supply pipelines have been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the new taps, compare the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the bath tub in the required placement. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the tub up until the level reviews level.
To mount taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression sign up with; then do the same for the other faucet.
Turn on the water system and inspect all joints and also new pipework for leaks and tighten them if needed. Fill up the bathtub and also examine the overflow outlet and also the normal electrical outlet for leakages.
Finally, deal with the bath paneling as described in the supplier's user's manual. Tiling and also sealing around the bathtub should wait up until the tub has been made use of a minimum of when as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making certain that the washers are in location between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former type should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to split a rigid seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing problems with moisture as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components as well as fittings. They are sold in tubes as well as cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealant can fracture fairly very early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader about Installing A Bathtub, I figured sharing that excerpt was a good idea. Sharing is nice. Helping others is fun. Many thanks for your time. Visit again soon.
Schedule Service Pickup